Quantcast
Channel: ToManual.com » Search Results » programming a tccm
Viewing all articles
Browse latest Browse all 10

1100F FORD PATS / SECURILOCK REMOTE START INTERFACE-DATA

0
0

Download PRODUCT ACCESSORIES DESCRIPTION The 1100F interface module is used when installing remote start products in Ford vehicles equipped with a factory immobilizer. The 1100F allows for easy interfacing between the remote start and the factory immobilizer, while maintaining the integrity of the OEM system. The factory transponder-based anti-theft system uses a small electronic chip hidden in the key to send a code to the vehicle’s transceiver when the ignition is energized. The key must be placed in the ignition and turned to the RUN position. This energizes a coil surrounding the key, which in turn energizes the chip, which sends a code to the vehicle. If the vehicle does not detect the code being sent, the vehicle will start and then immediately shut off or will just crank, and the anti-theft light will flash. The 1100F provides a valid code to the vehicle whenever it is remote started, but does not affect the immobilizer system during normal vehicle operation; the immobilizer system remains fully functional. MODULE WIRING Refer to the Transponder Cross Reference Chart and Vehicle Specific Transponder Connector Type to and install all wire according the wiring diagram below. Once all connections have been made, plug the module into the wiring harness and follow the programming steps below. PROGRAMMING STEPS STEP 1: SELECTS INSTALLATION MODE This procedure determines whether the module will operate using the conventional manner using the ground when running signal or a data type connection not used in this application. CAUTION: For security purposes this step is programmable only once. Please ensure the proper mode is activated. To change the installation mode, the module must be reset and reprogrammed. 1. Complete wire connections to vehicle and insert harnesses into module. 2. Press programming button once or twice to select the installation type. The LED will flash green the same number of times to confirm selection. 1. 1 x green flash = Unused installation mode. 2. 2 x green flashes = Standard installation mode. 3. To register your selection, press and hold the programming button until the green LED turns on solid. 4. The installation mode is now selected and programmed. STEP 2: DETERMINE TRANSPONDER TYPE Refer to the transponder cross reference chart to determine transponder type and programming procedure. 1. If the transponder type is 1, proceed to 2A. 2. If the transponder type is either 2 or 3, proceed to 2B 2A: TRANSPONDER TYPE 1 1. Insert the vehicle key into the ignition. 2. Turn ignition to the “ON” position and wait for the LED to illuminate green for two seconds. 3. Programming is complete. 2B: TRANSPONDER TYPE 2 OR TYPE 3 IMPORTANT: Both keys are required to complete the programming procedure. A maximum 5 second delay between each step is permitted. If the delay is exceeded, the vehicle will not allow programming to continue. The programming procedure must be restarted. 1. Insert the 1st key into the ignition. Turn ignition to the “ON” position, the LED will illuminate green. Wait for the car security light to turn off, turn ignition to the “OFF” position and remove the key. 2. Insert the 2nd key into the ignition. Turn ignition to the “ON” position and wait for the car security light to turn off. Turn ignition to the OFF” position and remove the key. 3. Press and release the programming button once and remote start the vehicle. Wait for LED to illuminate green for two seconds. Programming is complete. LED DIAGNOSTICS 1. During STEP 1, if the LED flashes red this indicates the wire connections are incorrect. 2. Once programming has been completed, if the LED flashes red the module failed to learn correctly. Reset module and repeat the programming procedure. 3. When the remote starter is engaged, the led will flash green to indicate the current transponder mode as follows. 1 x green flash = Type 1 2 x green flashes = Type 2 3 x green flashes = Type 3 If the LED remains illuminated red, the device is incorrectly programmed. FACTORY RESET Press and hold the programming button while inserting the power harness into the module. Release the programming button once the LED begins to flash. Module is now reset.


Viewing all articles
Browse latest Browse all 10

Latest Images

Trending Articles





Latest Images